Showing results: 601 - 615 of 2617 items found.
-
PeakTech Prüf- und Messtechnik GmbH
Uses voltage detection technology for the detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets and wires.
-
A&D Company, Ltd.
This testing machine evaluates the frictional characteristics of radial bearings. The circuit system adopted for the lubricant enables heating up to 80C.
-
MicroAmp2 -
Innovative Technical Systems
MicroAmp2 is a new series of RF/microwave prototyping boards and housings that allow for rapid construction of custom circuits in a fraction of the time and cost of traditional solutions. With the MicroAmp2 series of MB boards, a designer can quickly build amplifiers, filters, passive networks, multipliers, prescalers, log detectors, oscillators, and opamps using many popular components. A growing line of MB circuit boards are available to fit many of the industry-standard components, which can be easily assembled and mounted into shielded RF housings to create fully functional modules. Select parts from popular manufacturers such as Analog Devices, Avago, CEL, M/A-COM, Mini Circuits, RFMD, Triquint, and others.
-
DP-VME-2115 -
Data Patterns Pvt. Ltd.
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
-
Circuit Check, Inc.
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Circuit AOI -
Machvision
The Circuit AOI system is designed to perform automatic and accurate inspecting systems. It integrates rigid mechanical system with advanced vision technology and manufactured and tested by strict is standards. It is suitable for circuit inspection for PCB/FPC, verification and repair. Innovation and unique inspection algorithms are applied to inspect open, short, protrusion, nick, scratch, pin hole, island, line width/space violation, object missing and others defects. AOI system can use offline setup project and check results. It will improve the throughput.Compare to halogen lighting, the full angle LED lighting of Circuit AOI can obtain the best image contrast and is good for different panel type inspection.
-
Circuit ScanTM 1000 -
Micro Magnetics
Operating circuits within a semiconductor generate external magnetic fields near the surface of the device. These magnetic fields, while weak in strength, contain information about the spatial variation of current density flowing within the circuit. Micro Magnetics has developed the CS1000 to make practical use of this information and provide engineers with valuable information about what is going on inside circuitry non-destructively.
-
Setfos -
FLUXiM
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
ONT-8600AS -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 1310nm direct modulation fiber optical transmitter, adopts high linearity DFB laser of famous brand in the world, and builds-in perfect pre-distortion adjustment circuit and laser APC, ATC closed loop control circuit. All the operating parameters of fiber optical transmitter are controlled by microprocessor, and the LCD screen on the front panel can display relative operating status and the fault information.
-
DiagnoSYS Systems Ltd
The compact and portable Faultfinder VIP system, combined with a Laptop running TestVue software, provides a way to rapidly identify failures by troubleshooting a PCB or CCA. It uses impedance signatures (also known as VI testing) measured from a known working circuit and stores them as a test program. These stored signatures are then compared to the ones being measured on the suspect circuit to automatically determine if there is a fault.
-
Tripp Lite
Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. Includes handy storage pouch when not in use. Power supplied by 9V Battery (not included).
-
National Technical Systems
Fourier Transform Infrared Spectroscopy (FTIR) is a standard technique used in the identification of contaminating materials on the surface of printed circuit boards (PCBs) and around the leads of electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) on printed circuit assemblies (PCAs). Additionally, FTIR can be used for “simpler” identifications, such as determining a specific type of plastic or rubber compound.
-
NEO TELE-TRONIX PVT. LTD
These durable and modern Test Sets For Switchgear Industries are developed for determining the tripping of circuit in emergency or random current fluctuation. These testing systems save the outage and break-down of any electrical systems. They are designed to be used on multiple types of circuits. From voltage, current to vacuum, every factor is precisely tested to provide accurate results. They are easy to use and install sets available with user-friendly features.
-
National Technical Systems
Fourier Transform Infrared Spectroscopy (FTIR) is a standard technique used in the identification of contaminating materials on the surface of printed circuit boards (PCBs) and around the leads of electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) on printed circuit assemblies (PCAs). Additionally, FTIR can be used for “simpler” identifications, such as determining a specific type of plastic or rubber compound.
-
M-800P -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Model 800P is the world’s first clamp meter which can detect smallDC current in AC circuit in addition to general AC/DC current measurement.*By using this clamp meter, DC offset surveillance can be madeeasily in the actual fields like as solar inverters, etc. and it is possibleto check if the DC component in AC circuit is less than 1% ofthe rated AC current or not, according to the regulation.
